WASSERLÖSLICHER ABSTANDSRING FÜR MUFFENSCHWEISSUNGEN
US- UND AUSLANDSPATENTE ERTEILT |
HERGESTELLT IN DEN USA
Erzielen Sie mit SoluGap®, einem patentierten, wasserlöslichen Abstandshalter, jedes Mal einen präzisen, gleichmäßigen Spalt. Kein Anreißen, Messen oder Anpassen. Vollständig auflösbar.
EINZIGARTIGES DESIGN
FÜR JEDES METALL
Das patentierte, speziell entwickelte Design von SoluGap ist eine wirtschaftliche, zweckmäßige Lösung für Schweißmuffenanwendungen.
SoluGap gewährleistet den minimalen Luftspalt von 1/6″ (1,6 mm), wie in den militärischen Normen der US-Streitkräfte gefordert, ohne dass Sie vor dem Schweißen den Abstand messen oder schätzen müssen.
SoluGap, der stabilste wasserlösliche Schweißmuffen-Abstandsring auf dem Markt, verfügt über ein einzigartiges 3-Laschen-Design, das unabhängig von der Rohrausrichtung festen Halt gewährleistet.
SoluGap wird in den USA hergestellt und besteht aus umweltfreundlicher, wasserlöslicher Aquasol-Verbundpappe. Sie löst sich in den meisten Flüssigkeiten vollständig und schnell auf und ermöglicht somit ein einfaches Reinigen nach dem Schweißen.
Lieferbar in den verschiedensten Größen mit Durchmessern von 1/2″ bis 2″. SoluGap lässt sich leicht anbringen und ist gebrauchsfertig – die cleverste Lösung für Ihre Schweißmuffenanwendungen.







Revolutionäres Design
Steigert Effizienz und Einsparungen
Zahlreiche Anwendungsmöglichkeiten
Positionieren
Ring so positionieren, dass die Außenkante des Rings mit dem Innenumfang des Rohrs bündig ist.
Fixieren
Den Ring in das Rohr einführen, sodass die unter Spannung stehenden Ränder sich eng an die Rohrwand anlegen und auf die erforderliche Mindestfuge von 1/16″ einrasten.
Halten
Sobald der Ring im Rohr fixiert ist, bleibt er an Ort und Stelle, auch wenn die Muffe seitlich verschoben oder verdreht ist.
Schweißen
1. Rohr vor dem Heften ankippen, sodass es nicht flach aufliegt
2. 3 oder 4 Heftschweißungen ausführen, dabei die Zwischenlagenschweißtemperatur gemäß ASME B31.3 einhalten
3. Nach Herstellung der ersten Heftnaht das Rohr rechtwinklig ausrichten
4. Schweißvorgang fortsetzen, ohne die Zwischenlagenschweißtemperatur zu überschreiten
Entfernen
Warmes oder kaltes Wasser einleiten, um den Ring vollständig und rückstandsfrei aufzulösen.
| ITEM NO | DIMENSIONS | THICKNESS | DIAMETER | PACKAGING | MINIMUM ORDER |
|---|---|---|---|---|---|
| Nominal Pipe/Size (IN) | English (IN) | NOMINAL (DN) | |||
| SGP-0.50 | 1/2″ | 1/16″ | 15 | 50 Per Bag | 50 |
| SGP-0.75 | 3/4″ | 1/16″ | 20 | 50 Per Bag | 50 |
| SGP-1.0 | 1″ | 1/16″ | 25 | 50 Per Bag | 50 |
| SGP-1.25 | 1 1/4″ | 1/16″ | 32 | 50 Per Bag | 50 |
| SGP-1.50 | 1 1/2″ | 1/16″ | 40 | 50 Per Bag | 50 |
| SGP-1.75 | N/A | 1/16″ | N/A | 50 Per Bag | 50 |
| SGP-2.00 | 2″ | 1/16″ | 50 | 50 Per Bag | 50 |
| SGP-2.50 | 2 1/2″ | 1/16″ | 65 | 50 Per Bag | 50 |
| ITEM NO | DIMENSIONS | THICKNESS | DIAMETER | PACKAGING | MINIMUM ORDER |
|---|---|---|---|---|---|
| Nominal Pipe/Size (IN) | English (IN) | NOMINAL (DN) | |||
| SGP-0.375 | 3/8″ | 1/16″ | 10 | 50 Per Bag/1000 Per Box | 1000 |
| SGP-2.75 | N/A | 1/16″ | N/A | 50 Per Bag/1000 Per Box | 1000 |
| SGP-3.00 | 3″ | 1/16″ | 80 | 50 Per Bag/1000 Per Box | 1000 |
| SGP-3.25 | N/A | 1/16″ | N/A | 50 Per Bag/1000 Per Box | 1000 |
| SGP-3.50 | 3 1/2″ | 1/16″ | 90 | 50 Per Bag/1000 Per Box | 1000 |
| SGP-4.00 | 4″ | 1/16″ | 100 | 50 Per Bag/1000 Per Box | 1000 |
| ITEM NO | DIMENSIONS | THICKNESS | DIAMETER | PACKAGING | MINIMUM ORDER |
|---|---|---|---|---|---|
| Nominal Pipe/Size (IN) | English (IN) | Nominal (DN) | |||
| SGP-0.50/2 | 1/2″ | 1/8″ | 15 | 50 Per Bag | 50 |
| SGP-0.75/2 | 3/4″ | 1/8″ | 20 | 50 Per Bag | 50 |
| SGP-1.0/2 | 1″ | 1/8″ | 25 | 50 Per Bag | 50 |
| SGP-1.25/2 | 1 1/4″ | 1/8″ | 32 | 50 Per Bag | 50 |
| SGP-1.50/2 | 1 1/2″ | 1/8″ | 40 | 50 Per Bag | 50 |
| SGP-1.75/2 | N/A | 1/8″ | N/A | 50 Per Bag | 50 |
| SGP-2.00/2 | 2″ | 1/8″ | 50 | 50 Per Bag | 50 |
| SGP-2.50/2 | 2 1/2″ | 1/8″ | 65 | 50 Per Bag | 50 |
| ITEM NO | DIMENSIONS | THICKNESS | DIAMETER | PACKAGING | MINIMUM ORDER |
|---|---|---|---|---|---|
| Nominal Pipe/Size (IN) | English (IN) | Nominal (DN) | |||
| SGP-0.375/2 | 3/8″ | 1/8″ | 10 | 50 Per Bag/1000 Per Box | 1000 |
| SGP-2.75/2 | N/A | 1/8″ | N/A | 50 Per Bag/1000 Per Box | 1000 |
| SGP-3.00/2 | 3″ | 1/8″ | 80 | 50 Per Bag/1000 Per Box | 1000 |
| SGP-3.25/2 | N/A | 1/8″ | N/A | 50 Per Bag/1000 Per Box | 1000 |
| SGP-3.50/2 | 3 1/2″ | 1/8″ | 90 | 50 Per Bag/1000 Per Box | 1000 |
| SGP-4.00/2 | 4″ | 1/8″ | 100 | 50 Per Bag/1000 Per Box | 1000 |
| ITEM NO | DIMENSIONS | THICKNESS | DIAMETER | PACKAGING | MINIMUM ORDER |
|---|---|---|---|---|---|
| Nominal Pipe/Size (IN) | English (IN) | Nominal (DN) | |||
| SGP-0.50/M | 1/2″ | 1/16″ | 15 | 500 Per Bag/1000 Per Box | 1000 |
| SGP-0.75/M | 3/4″ | 1/16″ | 20 | 500 Per Bag/1000 Per Box | 1000 |
| SGP-1.0/M | 1″ | 1/16″ | 25 | 500 Per Bag/1000 Per Box | 1000 |
| SGP-1.25/M | 1 1/4″ | 1/16″ | 32 | 500 Per Bag/1000 Per Box | 1000 |
| SGP-1.50/M | 1 1/2″ | 1/16″ | 40 | 500 Per Bag/1000 Per Box | 1000 |
| SGP-1.75/M | N/A | 1/16″ | N/A | 500 Per Bag/1000 Per Box | 1000 |
| SGP-2.00/M | 2″ | 1/16″ | 50 | 500 Per Bag/1000 Per Box | 1000 |
| SGP-2.50/M | 2 1/2″ | 1/16″ | 65 | 1 Box of 500 | 1000 |
| ITEM NO | DIMENSIONS | THICKNESS | DIAMETER | PACKAGING | MINIMUM ORDER |
|---|---|---|---|---|---|
| Nominal Pipe/Size (IN) | English (IN) | Nominal (DN) | |||
| SGP-0.375/M | 3/8″ | 1/16″ | 10 | 1 Box of 500 | 1000 |
| SGP-2.75/M | N/A | 1/16″ | N/A | 1 Box of 500 | 1000 |
| SGP-3.00/M | 3″ | 1/16″ | 80 | 1 Box of 500 | 1000 |
| SGP-3.25/M | N/A | 1/16″ | N/A | 1 Box of 500 | 1000 |
| SGP-3.50/M | 3 1/2″ | 1/16″ | 90 | 1 Box of 500 | 1000 |
| SGP-4.00/M | 4″ | 1/16″ | 100 | 1 Box of 500 | 1000 |
Aquasol® Water Soluble Products, including SoluGap Water Soluble Socket Weld Spacer Rings, must be flushed with an aqueous solution or steam containing a certain percentage of water in order to be removed from the weld area. Please contact Aquasol for further information.
SoluGap Water Soluble Socket Weld Spacer Rings will not dissolve in oil or fuel. The products must be flushed with an aqueous solution or steam containing a certain amount of water in order to be removed from the weld area.
As metal pipes are heated and cooled, they expand and contract. Therefore, a minimum 1/16″ gap between the socket weld and the pipe is required to facilitate the fluctuation of the metal. Without this gap, cracking and loss of weld integrity can occur.
Typically, welders will spend time estimating the correct gap size, creating more room for error. With SoluGap, measuring and scribing are unnecessary. SoluGap is designed to create the perfect gap with ease by acting as a temporary space insert during welding that can later be flushed away by an aqueous solution.
Even with its firm structure, SoluGap is incompressible. For example, at 100 PSI compression load, SoluGap compresses by approximately 1 percent in thickness.
NOTE: This data was obtained through testing by the Aquasol engineering staff. The Aquasol Corporation recommends all users conduct their own tests, as this information is only a guideline for general reference purposes.
The heat temperature rating for SoluGap is approximately 400° F. This temperature rating should be sufficient, if all welding guidelines are adhered to for socket welds.
To ensure SoluGap Water Soluble Socket Weld Spacer Rings remain uncharred while welding and successfully dissolve during hydro testing, be sure not to exceed the interpass temperature of 300° F while following the proper ASME B31.3 code welding procedure.
The American Society of Mechanical Engineers provides companies with codes and standards, which cover a vast range of welding applications and processes. According to the ASME website, the organization has more than 130,000 members in 158 countries. Policy makers in Congress, the White House Office of Science and Technology and many key federal agencies look to the ASME for the latest engineering and technical information.
Aquasol® designed SoluGap to meet the standards and codes of the ASME in regards to its dimensions and other properties.
For further information on ASME, visit https://www.asme.org/.
Maintenance Repair Operations (MRO) are supported by items, including consumables like SoluGap Socket Weld Spacer Rings, that aid in the production process. MRO reports can show how many of these items are used by companies over a specific time period.
Some of the companies on the SoluGap MRO report include Chevron, Shell Oil, BP North America, Sunoco and many more.
Aquasol® distributes its patented, revolutionary products to over 80 countries worldwide. Many large companies have successfully tested and approved SoluGap as spec items in welding operations. Some of these include, ExxonMobil, Shell, Saudi Aramco, Conoco Phillips, Bechtel, KBR, Hyundai, CCC, Chevron, Jacobs, Petrofac, and Tecnicas Reunidas.
When using SoluGap, no specific safety precautions are necessary. SoluGap is manufactured from CE and EPA-approved water soluble material that is completely environmentally friendly.
SoluGap is used in various industries where socket welding is required.
Some of these manufacturing areas include:
Aquasol® distributes its patented, revolutionary products to over 80 countries worldwide. Many large companies have successfully tested and approved SoluGap as spec items in welding operations. Some of these include, ExxonMobil, Shell, Saudi Aramco, Conoco Phillips, Bechtel, KBR, Hyundai, CCC, Chevron, Jacobs, Petrofac, and Tecnicas Reunidas.
When using SoluGap, no specific safety precautions are necessary. SoluGap is manufactured from CE and EPA-approved water soluble material that is completely environmentally friendly.
Aquasol® Water Soluble Products, including SoluGap Water Soluble Socket Weld Spacer Rings, must be flushed with an aqueous solution or steam containing a certain percentage of water in order to be removed from the weld area. Please contact Aquasol for further information.
SoluGap Water Soluble Socket Weld Spacer Rings will not dissolve in oil or fuel. The products must be flushed with an aqueous solution or steam containing a certain amount of water in order to be removed from the weld area.
As metal pipes are heated and cooled, they expand and contract. Therefore, a minimum 1/16″ gap between the socket weld and the pipe is required to facilitate the fluctuation of the metal. Without this gap, cracking and loss of weld integrity can occur.
Typically, welders will spend time estimating the correct gap size, creating more room for error. With SoluGap, measuring and scribing are unnecessary. SoluGap is designed to create the perfect gap with ease by acting as a temporary space insert during welding that can later be flushed away by an aqueous solution.
Even with its firm structure, SoluGap is incompressible. For example, at 100 PSI compression load, SoluGap compresses by approximately 1 percent in thickness.
NOTE: This data was obtained through testing by the Aquasol engineering staff. The Aquasol Corporation recommends all users conduct their own tests, as this information is only a guideline for general reference purposes.
The heat temperature rating for SoluGap is approximately 400° F. This temperature rating should be sufficient, if all welding guidelines are adhered to for socket welds.
To ensure SoluGap Water Soluble Socket Weld Spacer Rings remain uncharred while welding and successfully dissolve during hydro testing, be sure not to exceed the interpass temperature of 300° F while following the proper ASME B31.3 code welding procedure.
No, the sensors are built-in. The device must be returned to Aquasol’s USA or Middle East Facility at this time only. the POM like the P-OX 100 device?
No, only use the provided charger
No, only use the provided charger
SoluGap is used in various industries where socket welding is required.
Some of these manufacturing areas include:
The American Society of Mechanical Engineers provides companies with codes and standards, which cover a vast range of welding applications and processes. According to the ASME website, the organization has more than 130,000 members in 158 countries. Policy makers in Congress, the White House Office of Science and Technology and many key federal agencies look to the ASME for the latest engineering and technical information.
Aquasol® designed SoluGap to meet the standards and codes of the ASME in regards to its dimensions and other properties.
For further information on ASME, visit https://www.asme.org/.
Maintenance Repair Operations (MRO) are supported by items, including consumables like SoluGap Socket Weld Spacer Rings, that aid in the production process. MRO reports can show how many of these items are used by companies over a specific time period.
Some of the companies on the SoluGap MRO report include Chevron, Shell Oil, BP North America, Sunoco and many more.
Aquasol® distributes its patented, revolutionary products to over 80 countries worldwide. Many large companies have successfully tested and approved SoluGap as spec items in welding operations. Some of these include, ExxonMobil, Shell, Saudi Aramco, Conoco Phillips, Bechtel, KBR, Hyundai, CCC, Chevron, Jacobs, Petrofac, and Tecnicas Reunidas.
Restart the unit and try again.
This is normal, there is a delay for the flash drive to appear
The Maximum reading it can show is 20.9%. The unit should not be exposed to Oxygen concentration greater than 21%. It may damage the sensor and void the warranty
No, don’t use with any sticky gas. It may damage the sensor and void the warranty